全自動自上料攪拌車攪拌軸停止轉動的原因有哪些?

 來源:http://m.servimetrol.com 日期:2022-11-14 發布人:jufeng
自動上料攪拌車集上料、攪拌為一體,節省人力物力,被廣泛應用。自動上料攪拌車如有物料那么不能停止攪拌,防止物料凝固,有不少客戶遇到過自上料混凝土攪拌車在使用的過程中會出現攪拌軸停止轉動的現象,出現這種情況一般都是什么原因造成的呢?下面小編為大家講解攪拌軸出現停止轉動這種情況的原因:
The automatic feeding mixer integrates feeding and mixing, saving manpower and material resources, and is widely used. If there are materials in the automatic feeding mixer, the mixing cannot be stopped to prevent the materials from solidifying. Many customers have encountered the phenomenon that the mixing shaft stops rotating during the use of the self feeding concrete mixer. What are the reasons for this? The following section explains why the mixing shaft stops rotating:
自上料攪拌車攪拌軸停止轉動的原因及解決方法
Reasons and Solutions for Stopping Rotation of Mixing Shaft of Self feeding Mixer Truck
在生產過程中當出現混凝土自上料攪拌車攪拌軸停止轉動或是轉動有點緩慢都是不正?,F象,如果出現這種情況首先停機檢查,看看有沒有出現下列三種情況。
During the production process, it is abnormal for the concrete to stop rotating from the mixing shaft of the loading mixer or rotate slowly. If this happens, stop the machine first to check whether the following three conditions occur.
1、電機傳動皮帶有沒有出現松動的情況?
1. Is the motor drive belt loose?
自拌混凝土攪拌車電機傳動皮帶過松也能導致商品混凝土拌合機攪拌軸轉動緩慢或者停止轉動,電機傳動皮帶過松,導致傳遞的動力不足。
The loose motor drive belt of self mixing concrete mixer can also cause the mixing shaft of commercial concrete mixer to rotate slowly or stop rotating, and the loose motor drive belt can cause insufficient power transmission.

2、有沒有嚴重超載?
2. Is there any serious overload?
自拌混凝土攪拌車攪拌軸如果超過正常工作負荷,會使攪拌軸轉動緩慢,若負荷過大,就會導致攪拌軸停轉或者是攪拌軸彎曲。
If the mixing shaft of self mixing concrete mixer exceeds the normal working load, the mixing shaft will rotate slowly. If the load is too large, the mixing shaft will stop or bend.
3、攪拌葉片或側葉片與筒體內壁間有沒有大的異物?
3. Is there any large foreign matter between the mixing blade or side blade and the inner wall of the cylinder?
出現這種情況也會使混凝土自動上料攪拌車攪拌軸停止轉動或轉動緩慢。攪拌葉片或側葉片與罐內壁間有較大的異物也會導致攪拌軸停轉,之所以能卡存異物,就是由于攪拌葉片或側葉片與罐內壁間隙過大造成的,尤其是石子。
In this case, the mixing shaft of the automatic concrete feeding mixer will stop rotating or rotate slowly. Large foreign matters between the mixing blades or side blades and the inner wall of the tank will also cause the mixing shaft to stop. The reason why foreign matters can be stuck is that the clearance between the mixing blades or side blades and the inner wall of the tank is too large, especially stones.
以上就是為大家介紹的有關全自動自上料攪拌車的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.servimetrol.com/
The above is a detailed introduction to the fully automatic self loading mixer, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our attitude http://m.servimetrol.com/